Skip to content
10 active vans · 24/7 · London & the M25
ResidentialCommon faults
Get in touch
Book an engineer
Drainage and blockages guides →

Grease trap problems: cleaning, capacity or drainage repair?

A commercial kitchen that backs up around a grease trap needs the trap and connected drainage route assessed before clearance is chosen. The restriction may be within the unit, at its outlet or farther downstream. Stop the affected discharge if wastewater is escaping and arrange a safe investigation rather than adding chemicals or assuming the trap alone is responsible.

Loyal Plumbers · Updated

Discuss your property work

Describe the operational failure, not just the unit name

Tell the contractor which sinks or appliances are backing up, whether the trap is overflowing and whether other drains remain usable. A unit that appears full is not enough to identify the failed flow path. The type and model, recent cleaning record and timing of the problem help establish what needs inspecting.

Do not continue discharging hot wastewater to see whether it clears. Keep staff away from contaminated overflow and wet electrical equipment. The site manager needs to decide which facilities remain safely usable while the affected route is assessed. A plumber clearing one connection does not by itself authorise the kitchen to resume every activity.

The trap and downstream drain are connected but distinct

Grease-management equipment separates material from the wastewater passing through it, while the connected drain still needs a clear route. A restriction beyond the unit can cause water to back up even when attention has recently been given to the trap. Conversely, a local accumulation can limit flow without proving that the whole drain is damaged.

ACO publishes installation and maintenance information for specific grease-trap arrangements. The attending contractor should identify the installed unit and relevant access before opening it. This fault visit should answer where flow is being restricted and what work will restore it; longer-term equipment selection and maintenance planning are separate decisions once the immediate findings are known.

If the external gully or manhole is backing up as well, the blockage is past the trap. Our guide to a blocked outside drain covers what to check and when it needs clearing.

Signs a grease trap is full or blocked

Most kitchens notice the same pattern first: sinks empty more slowly through a busy service, water gurgles or stands in the pot wash, and a stale fat smell builds near the unit. A trap that has reached its capacity lets fat pass straight through to the drain, so the blockage often shows up downstream before anyone lifts the lid.

Note which of these you are seeing and when they started. If the slow drainage improves after the unit has been emptied, capacity or emptying frequency is the likely issue. If it returns within days, or the unit was emptied recently and the kitchen still backs up, the restriction is more likely at the outlet or in the drain beyond it.

  • Slow draining at sinks and pot wash, worst during or after service.
  • Water backing up into the sink connected to the trap.
  • Gurgling from nearby floor gullies when the dishwasher empties.
  • Fat or rancid smells around the unit or the outside manhole.
  • Visible fat or solids in the outside chamber or gully.

Why a grease trap smells and when size is the problem

A smell on its own does not always mean a blockage. It can come from a unit overdue for emptying, a damaged lid seal or poor ventilation of the drain. Our guide on why grease trap smells need investigating separately walks through those causes.

A trap that fills far faster than the emptying schedule allows may simply be too small for the menu and number of covers. Sizing a grease separator for a commercial kitchen explains the information needed to check that.

Keeping grease separator maintenance records shows whether the problem is getting worse over time.

Prepare safe access to the affected equipment

Provide the unit location, available working space and the person authorised to stop connected fixtures. Equipment below sinks or within a service area may be difficult to reach while the kitchen is operating. Agree a safe working zone and any handling arrangements rather than expecting a contractor to open a cover beside active food preparation.

Do not remove heavy lids, enter a chamber or reach into retained waste yourself. The contents and condition can introduce hazards beyond an ordinary sink trap. Tell the contractor about chemicals previously added and any specialised cleaning undertaken. That information affects the method and the appropriate people or equipment needed for the work.

Choose clearance from the condition and route

The method needs to suit the unit, connected pipework and material present. Removing retained material from the trap is different from clearing a blocked outlet or investigating a damaged downstream run. The proposal should identify which task is being undertaken and what evidence supports it.

A generic instruction to jet every part of the installation can be inappropriate. The contractor should account for the product’s requirements and avoid damaging internal components or forcing contamination elsewhere. Do not use an unapproved chemical or enzyme product as an emergency substitute for finding the blockage. Any waste handling and disposal arrangements should be agreed with the responsible service provider.

Escalate only where the first findings justify it

If the unit is cleared but discharge remains restricted, the next step may concern the outlet or downstream drainage. The contractor should explain what has been established and what remains uncertain. A defined camera inspection or further access can be useful where it answers that remaining question, rather than being added automatically to every clearance.

Costs depend on access, retained material handling, the location of the restriction and any separate drain work. Agree approval points before extending the job beyond the first affected section. If damage is found, distinguish the repair proposal from the clearance already completed. A flowing outlet after one brief test does not prove that an unidentified recurring defect has disappeared.

Check restored flow and communicate remaining restrictions

The completion check should reflect the connected fixtures and the original backup pattern using an appropriate controlled method. The handover needs to state what was cleared, whether accessible connections remain sound and which areas were not inspected. If another service is needed before normal operation, name that dependency clearly.

Keep the findings with the kitchen repair record, including the unit reference and any downstream defect identified. This supports a later recurrence investigation without turning the fault article into a generic maintenance schedule. The important immediate outcome is a known flow path, a documented repair boundary and clear information for the person deciding how the premises returns to use.

Arrange a blockage assessment for the kitchen

Loyal Plumbers can discuss commercial kitchen drainage investigation and the agreed plumbing clearance or repair scope across London and inside the M25. Provide the postcode, affected fixtures, trap model if known, current overflow and available shutdown window. We clarify any specialist waste-handling requirements and site access. Reports or safe photographs can be shared by email after the initial enquiry.

If the kitchen is backing up now, call 020 4652 8585. We attend 24/7, including after service closes, and the call-out is £60. Planned kitchen drainage and appliance work sits under our commercial plumbing service.

Common questions

Does an overflowing trap mean it needs replacement?
Not automatically. The restriction may be local or downstream. The condition and flow path need establishing before choosing equipment replacement.
Can I keep using other connected sinks?
Do not assume they discharge independently. Identify the affected route and follow the site’s safe-use arrangements while the blockage is assessed.
Is clearing the trap the same as clearing the drain?
No. They are related but distinct sections. The work record should say which was inspected or cleared and what further restriction remains, if any.
How often should a grease trap be emptied?
It depends on the unit's capacity and how much fat the kitchen produces, so follow the manufacturer's guidance and adjust it to what inspections find. If the unit is regularly close to full at each emptying, shorten the interval or review whether it is big enough.
Why is my grease trap blocked again soon after cleaning?
Either the unit is undersized for the kitchen's output, or the restriction is in the outlet or the drain beyond it. Emptying the trap does not clear fat that has already built up downstream.
Can I pour a drain chemical into a blocked grease trap?
No. Strong chemicals can damage the unit, push fat further into the drain where it sets again, and make the job more dangerous for whoever clears it. Stop using the connected sinks and get the route assessed.

Sources and further reading

Need help with this in London?

Emergency repairs, investigations and planned installations across London and inside the M25. Tell us what you need so we can agree the next step.

Discuss your job