Boiler losing pressure: causes and next steps
A boiler that keeps losing pressure is losing water from its sealed heating system, and the cause needs finding rather than repeated topping up. The water loss may be at a radiator, concealed pipework or the boiler, while expansion or pressure-relief problems can create a pattern of rising and falling readings. Repeatedly topping up does not establish which fault is responsible.
Loyal Plumbers · Updated
Get help with this problemReadings need context
Write down the pressure when the system is cold and, if it operates normally and safely, note what happens during an ordinary heating cycle. Use the correct appliance instructions for the acceptable range. A number taken while hot is not directly comparable to one taken after the system has cooled.
Also record how quickly the reading changes: over weeks, overnight, or within one cycle. Tell the engineer whether the boiler stops with a code and whether pressure loss began after bleeding radiators or other work. The timing helps shape an investigation without proving a particular component has failed.
The boiler gauge is not your tap pressure
The gauge on a sealed heating installation usually shows pressure in the heating circuit. This is different from the incoming water pressure at a kitchen tap. Weak shower flow and a low boiler gauge may be separate problems, so describe each symptom instead of assuming one explanation.
Not all heating systems use the same arrangement. Some are open vented rather than sealed and may not have an equivalent filling procedure. If you cannot identify the system, provide photographs of the boiler and its visible controls; do not search for a valve to turn based on a different model’s instructions.
Visible water loss is useful evidence
Look from a safe, accessible position for dampness around radiators, valves and exposed pipework. A small leak can leave staining rather than a large puddle. Tell the professional exactly where marks appear and whether the surface becomes wet again during use.
Do not tighten hot fittings, remove floorboards or reach inside the boiler. If water is reaching wiring, switches or other electrical equipment, keep clear and request urgent help. The aim of your observations is to locate clues, not to disturb a potentially pressurised or unsafe installation.
No visible leak does not rule out a problem
Pipework may run beneath floors or behind finished surfaces. The appliance can also require internal examination, and water may leave through a discharge route that is not obvious from indoors. The investigation should therefore distinguish the boiler from the wider heating circuit before disruptive access is proposed.
Ask how the suspected location will be tested and what evidence would justify opening a floor or wall. Leak detection can be a separate scope where hidden pipework is involved. Tell us about access hatches, recent renovations and known pipe routes, but do not start removing finishes in anticipation of a diagnosis.
Pressure rises sharply, then falls when cold
A repeated large rise during heating followed by a low cold reading can indicate that expansion or relief arrangements need examination. It is a pattern to report, not proof that a specific part needs replacement. Take photographs of the gauge at different times if safe, rather than repeatedly changing the filling pressure.
An externally visible discharge pipe may provide a clue if it releases water. Observe only from a safe position and do not touch the discharge, which may be hot. Never plug, cap or redirect a relief outlet to stop water loss; the function and cause need professional assessment. If your gauge is sitting high rather than low, see our guide to boiler pressure too high.
Should you top up the pressure?
Manufacturers provide model-specific user guidance for some systems. If your manual permits a user top-up, its instructions and limits apply; this page does not substitute a universal filling procedure. Do not proceed if you are unsure of the control, the system is leaking actively or there is any electrical or hot-water hazard.
When the pressure repeatedly falls, arrange diagnosis rather than treating refilling as an ongoing solution. Repeated topping up makes it harder to describe the original rate of loss and does not address the source. Tell the engineer how often you have needed to do it and any changes you have noticed.
What the assessment should establish
The professional should assess the pressure behaviour and relevant parts of the installation, then explain the finding and proposed work. A pressure gauge reading alone is not a reason to sell a new boiler. Repair may involve an appliance component, a radiator connection or pipework elsewhere.
Work on the gas boiler and its relevant connections must be undertaken by an appropriately qualified Gas Safe registered engineer. Do not remove the casing or attempt internal pressure, gas or electrical tests yourself. Ask what further checks are required if the initial visit cannot establish the source with confidence.
What should boiler pressure be?
Most combi and system boilers are set up to sit at roughly 1 to 1.5 bar when the heating is cold, rising a little while it runs. Your boiler manual gives the exact range, and many gauges mark it in green. If the pressure falls too low, many boilers stop and show a low-pressure fault; at around 3 bar the pressure relief valve on a typical sealed system is designed to open.
Compare readings taken in the same state. A reading of 1.8 bar with the heating hot and 1.2 bar when cold is normal expansion, not a loss. A cold reading that is lower each morning is the pattern that needs investigating.
Where the water usually goes
A sealed heating system should not need regular topping up, so a falling reading means water is leaving somewhere. These are the places an engineer will normally check first. Our guide to a heating leak or mains water leak explains how the two are told apart when there is a damp patch but no obvious source.
- A weeping radiator valve, bleed screw or pipe joint, often showing as staining rather than a puddle.
- The pressure relief valve discharge pipe, usually a copper pipe running outside from the boiler. A drip or a wet end after the heating has run suggests the valve is opening or letting by.
- Inside the boiler casing, which should only be investigated by a Gas Safe registered engineer.
- An expansion vessel that has lost its charge, which makes the pressure climb when hot and drop when cold, often with water from the relief pipe.
- Pipework under floors or in walls, sometimes shown by a damp patch, a ceiling stain or a warm area of floor.
- Recently bled radiators, which release water as well as air.
Measure how fast it is dropping
The rate of loss is one of the most useful things to report. After topping up once as the manual describes, note the cold reading and the time, then check at the same time each day. Losing a fraction of a bar over several weeks is a different job from losing a whole bar overnight, and it changes whether leak detection, a relief valve check or an expansion vessel replacement should come first.
Request help with recurring pressure loss
Loyal Plumbers provides boiler assessment and leak investigation across London and inside the M25, with 10 active vans and 24/7 operation. Send the make and model, cold readings, the time taken to lose pressure and any visible leakage in your enquiry; any photographs can follow by email. Say if heating or hot water has stopped completely.
If you are in a managed property, explain access to cupboards, risers and relevant rooms and who can approve investigative work. After repair, retain the findings and follow the professional’s operating advice. If pressure changes again, share the recorded pattern so the follow-up can address evidence rather than a guessed replacement part.
Start with written details in the enquiry form. If photographs would help, the team can request them by email after your initial enquiry; the form does not accept image uploads. Only take photographs where access is safe.
Common questions
- Is an occasional pressure change normal?
- Readings change with temperature, and the correct operating range depends on the system. A recurring loss or repeated need to refill should be assessed rather than dismissed as a normal temperature change.
- Can radiator leaks make the boiler lose pressure?
- Yes, a leak on a sealed heating circuit can affect its pressure. A visible radiator leak is useful evidence, but the rest of the system may still require assessment.
- Will replacing the boiler stop pressure loss?
- Only if it addresses the actual cause. A new appliance cannot repair leaking distribution pipework, so locate the fault before choosing replacement.
- What should my boiler pressure be?
- For most sealed systems, around 1 to 1.5 bar when cold and a little higher when the heating is running. Check your boiler manual for its own range.
- Why does my boiler keep losing pressure when there are no leaks?
- Water can leave through the pressure relief valve's outside pipe, from inside the boiler or from pipework you cannot see. A failing expansion vessel can also make the pressure swing. These need testing rather than repeated topping up.
- Is it safe to keep topping up the pressure?
- Occasional topping up as the manual describes is normal. Needing to do it every few days means water is escaping and fresh water keeps entering the system, which can shorten the life of components. Book an inspection.
Sources and further reading
Need help with this in London?
Emergency repairs, investigations and planned installations across London and inside the M25. Tell us what you need so we can agree the next step.
Discuss your job