Skip to content
10 active vans · 24/7 · London & the M25
ResidentialCommon faults
Get in touch
Book an engineer

London-wide plumbing & heating

Megaflo installation in London

We survey, specify and install Megaflo hot-water cylinders for homes and planned property upgrades. Mains flow, demand, heat source and safety-discharge routes determine the right installation.

  • Choose the appropriate cylinder arrangement
  • Check supply, space and discharge routing
  • Install and explain model-specific care
Cylinder connections and insulated pipework during plumbing work
Emergency Repairs London work archive
10 active vans24/7 emergency responseAll London boroughs · Inside the M25

£5 million public liability insurance Gas work carried out by Gas Safe registered engineers. About our company →

Let’s get your job moving.

Tell us where you are and whether you need urgent help or a planned visit.

The work we handle

Loyal Plumbers installs and replaces Megaflo hot water cylinders across London and inside the M25. We survey the supply, household demand and installation space, specify the appropriate model and complete the agreed pipework, controls and commissioning. Your proposal covers the cylinder and the surrounding work needed to bring it into service.

Choose the appropriate cylinder arrangement

Assess capacity and the relevant direct or indirect configuration against the way the property uses hot water.

Check supply, space and discharge routing

Review mains performance, installation access and the safety arrangements required for the selected model.

Install and explain model-specific care

Commission the installation and explain its controls, supplied documentation and maintenance requirements.

A clear route for your property.

Different faults and projects need different work. These are the main options for this service.

Discuss a Megaflo installation
Replace an existing Megaflo
Check the current model and connections; a similar-sized unit still needs a survey of the installation and discharge arrangements.
Install Megaflo in a different system
Conversion needs checks on supply and demand and may require changes to pipework, controls and the existing storage arrangement.

From first enquiry to the next step

  1. Review the current hot-water setup

    We ask about demand and inspect the supply and cylinder location.

  2. Confirm model and scope

    We explain the proposed cylinder and any changes needed to support it.

  3. Install and commission

    We check the completed system and hand over the model’s operating and servicing guidance.

Agree the rates and scope before work starts. £60 call-out. Hourly rate agreed before we attend. For installations and larger work, the proposal sets out the agreed scope and price.

How our pricing works

Service details & practical advice

The work explained, answers to common questions and related services.

Choose the right Megaflo installation

We establish the existing heat source and the intended hot water use before selecting the cylinder. Heatrae Sadia’s Megaflo range includes direct and indirect models and configurations for different space and system requirements. The installation proposal names the model and capacity so the product and connections are clear.

For a replacement, we check the existing cylinder label and layout, then identify what can be retained and what needs changing. Megaflo is a specific brand rather than a name for every unvented cylinder. If another model better suits the supply or available space, we explain that option as part of the survey.

Assess supply and hot water demand

We review incoming water performance, distribution pipework and the taps or showers expected to run together. The survey also considers capacity, heat-source recovery and controls. These details establish the specification rather than a simple like-for-like size assumption.

If the current system runs cold early or delivers weak flow, we establish the pattern before deciding what the replacement must address. A larger vessel will not correct every supply or control issue. The proposal identifies the work needed to meet the intended use and any limitation that remains outside it.

Replacing an existing Megaflo Eco

For a Megaflo Eco replacement, send the complete model designation and capacity from an accessible label, along with the reason for replacement. The manufacturer provides separate direct and indirect information. Identify the current heat source, ordinary controls and service history so the proposed unit can be compared with the actual installation.

A replacement survey checks the cylinder connections, surrounding components, removal route and future service space. It also separates a vessel problem from a repairable immersion, control or valve fault. If the agreed solution changes the capacity or heating arrangement, the quotation identifies the associated pipework, controls and commissioning instead of treating the new cylinder as a self-contained purchase.

Space includes access for the whole installation

A narrow cupboard can make a slimline option worth considering, but reduced diameter alone is not enough to establish suitability. Overall height, connections, removal route and service access still matter. Allow the survey to consider future maintenance before shelves or boxing are built around the new cylinder.

The discharge route also influences location. Moving the unit into a more convenient cupboard may require additional pipework or building work. Ask the proposal to identify that work rather than treating it as an unspecified extra after delivery. Flats may also need consent or access through communal parts of the building.

Expansion arrangements are model-specific

Megaflo documentation includes models with an internal air-gap expansion arrangement. This does not make an air-gap procedure appropriate for every cylinder on which someone uses the Megaflo name. The installed model and current instructions determine the relevant maintenance and fault response.

If you are enquiring because a tundish drips, request assessment of the existing system before assuming a new installation is needed. Do not manipulate relief valves, obstruct discharge or follow a generic online recharge procedure. A repeated symptom needs a cause identified, not merely a temporary change in visible flow.

Install, commission and document the system

The installation scope includes the selected cylinder, associated controls and safety arrangement, necessary connections and commissioning. We identify the applicable building-control route and the responsibilities for electrical or gas work where those tasks form part of the project.

Heatrae Sadia requires competent installation of unvented products. The work needs relevant unvented competence, including the applicable G3 requirements in England, with separate competence for electrical and gas tasks. The handover provides the relevant installation records and explains the ordinary user controls and service access.

A complete cylinder replacement scope

We specify the cylinder and capacity, pipe alterations, controls, discharge work and removal of old equipment. Access openings and making good are identified in the proposal, along with work provided by other trades. This gives owners and managing agents a clear basis for approving the installation.

Product warranty and registration details are confirmed for the selected model and premises. Vessel and component cover can differ, and manufacturer conditions still apply. We keep those product terms distinct from the installation work and explain the ongoing maintenance requirements at handover.

Prepare for disruption and ongoing servicing

Explain whether the property has one hot water source and whether tenants or vulnerable occupants need arrangements during the changeover. The expected interruption should be agreed after the scope is known. A relocation or conversion can involve different dependencies from an accessible replacement.

At handover, ask for model information, the relevant records and a demonstration of ordinary controls. Keep the service instructions available for future appointments. Arrange ongoing maintenance according to the manufacturer’s requirements and report new leaks or discharge promptly rather than assuming a recently installed cylinder cannot develop a fault.

Request a Megaflo project survey

Loyal Plumbers operates 24/7 with 10 active vans across all London boroughs and inside the M25. Send the postcode, existing system details and whether your project is a new installation, conversion or replacement. Include the proposed use and any access constraints so the survey addresses the actual property.

Describe the existing hot water arrangement and any planned bathroom changes. Mention available photographs or drawings; the team can arrange email sharing before the survey. Take photographs only from safely accessible positions.

Common questions

Are all unvented cylinders Megaflo?

No. Megaflo is a specific Heatrae Sadia brand. Read the label before ordering parts or selecting manufacturer instructions.

What installer qualifications should I check?

Ask for relevant unvented competence, including G3 qualifications for the work in England. Electrical work and any gas work also need their appropriate competence.

Can I choose the cylinder before a survey?

You can identify a preference, but capacity, supply, heat-source compatibility, access and discharge arrangements should be checked before an order is committed.

Sources and further reading

Useful guides for this service

Explore all boilers, cylinders and hot water guides →

Need help with this in London?

Emergency repairs, investigations and planned installations across London and inside the M25. Tell us what you need so we can agree the next step.

Discuss your job